360彩票

  • BAECO ODL-721 laser light source rear projection DLP splicing display unit

BAECO ODL-721 laser light source rear projection DLP splicing display unit

Device type: Large screen splicing

Keywords: mosaic display unit, large screen mosaic display wall, mosaic display system

Product description: Barco's flagship laser rear-projection splicing display unit uses the latest three-color pure laser technology, so it can display unprecedented brightness and vivid colors, and the total investment cost (TCO) is very low. With the 10th-generation rear-projection splicing display unit, Barco once again improved

BAECO ODL-721 laser light source rear projection DLP splicing display unit product introduction

Barco's flagship laser rear projection splicing display unit uses the latest three-color pure laser technology, so it can display unprecedented brightness and vivid colors, while the total investment cost (TCO) is very low. With the 10th generation rear-projection splicing display unit, Barco has once again raised the bar in the field of visualization of key infrastructure markets.

Its brightness is 2 times higher than the mainstream LED light source rear projection splicing display unit. All the brightness problems of the previous splicing display unit can be avoided in this flagship laser series. Since the high brightness allows it to work in daylight conditions, the control room can finally see the sun again, which improves the operating conditions of the operator! Coupled with the bright colors, all the nuances are clearly visible, so there is no misjudgment, and the environmental insight is also improved.

Uninterrupted operation for more than 11 years

With this flagship laser splicing display unit for all-weather control rooms, Barco has taken another huge step forward in terms of reliability. In energy-saving mode, its service life exceeds 100,000 hours, which means that operators can enjoy 24/7 uninterrupted operation for up to 11.5 years. All key components, including power supplies, input devices, and drives, are redundant to ensure uptime and give you peace of mind. Unlike other laser phosphor technologies used in non-24 / 7 conference rooms, Barco's flagship laser display series does not require a rotating color wheel to operate. Each color can be controlled independently and does not depend on the part of the color wheel, so this series can provide an unprecedented color control method, and color deviation will never occur.

Automatic calibration and adjustment

The engine suitable for Barco's flagship laser splicing display unit in the 24/7 control room has been fully electrically adjusted. Installation and maintenance personnel can perfectly align the entire spliced display unit without opening a single module. By using a network interface, only one technician is required to remotely calibrate the mosaic display unit, including keystone correction. This technology is more efficient, reliable, and time-saving, reducing calibration workload by 50% during installation. In addition, the Sense X color automatic calibration system continuously measures and adjusts the brightness and color gradation of the entire mosaic display unit. The user can be sure that the entire picture is always in perfect balance.

Device parameters:

Resolution: Full HD (1920 x 1080 pixels)

Screen contrast: 1800: 1

Color: up to 170% of EBU color area

LCD technology: DLP rear projection technology

White point: Customized white point color temperature

Brightness uniformity:> 95% ANSI 9 (typical)> 90% ANSI 13 (typical)

Screen gap: depends on screen type

Color stability: Sense X automatic color calibration

size:

• Diagonal: (approximately) 70 "

• Width: 1550 mm | 61.02 "

• Height: 872 mm | 34.33 "

• Thickness: 622 mm | 24.49 "

• Weight: Projection module: <63 kg | 139 lbs

• Weight: Stand: <39 kg | 86 lbs

Light source: RGB laser illumination (laser level 2)

Redundancy: redundant laser group and redundant power drivers, input signals and external power

Light source life:

> 100,000 hours in economy mode

> 80,000 hours in standard mode

Noise level: less than 20 dB (measured from 3 meters in front)

Operating conditions: 10 ° C-40 ° C | 50 ° F-104 ° F

Maximum humidity is 80% (non-condensing)

AC input voltage: 100-240 VAC, 50-60 Hz

power:

120W (economic)

200W (standard)

Cooling: 390 BTU / h (energy saving)

680 BTU / h (typical)

860 BTU / h (maximum)

Signal: redundant dual-link DVI

Pixel clock: 330 MHz

Input frequency: 24-62 Hz

Genlock: 49 – 61 Hz

Minimum frame delay: The minimum frame delay is 1 frame, and the delay in all other cases is less than 2-3 frames at full frame rate

Signal processing: loop-through, crop and zoom, use wall configuration

Direct Ethernet access: built-in web server

Graphical user interface: all settings and operating parameters

Integrating third-party equipment: WEB maintenance API

Warranty period: 2 years

* The pictures and technical specifications are for reference only. The original manufacturer reserves the right to improve or change the appearance or technical specifications of the product without prior notice.